How to Repair a Concrete Floor

In spite of the concrete finisher's best efforts, sometimes the finished product has significant imperfections. Even a carpet laid on a pad or vinyl flooring cannot be expected to cover up every flaw, so repairing a slab is the builder or homeowner's best choice for correcting the problem. Before patching, make sure your concrete is structurally sound. Much like medicine, it is better to treat the cause than just address a symptom. Sometimes surface defects are a clue that there is a bigger problem at hand. Have a professional assess whether patching is the right solution.


  1. Image titled Repair a Concrete Floor Step 1
    Determine the scope of the problem. The illustrations in this article show a repair where a slab reinforcing bar was too near the surface, and the concrete cracked. Other possible problems may include the following.
    • Ridges or humps left by the finishers.
    • Expansion or contraction cracks. Properly installed concrete should have joints that prevent this unsightly cracking. For a 4-inch thick slab, joints should be spaced 8 to 12 feet apart. If jointing is not sufficient, or improperly placed, cracks can occur. Typically these cracks are not structural and only need to be repaired for aesthetic purposes.
    • Debris like chunks of wood floating out of the concrete while it is still plastic (wet).
    • Damage caused by heavy objects being dropped on the slab before it is cured.
    • Surface scaling caused by improper finishing or freezing temperatures during curing. Scaling is when parts of the concrete surface flake away.
  2. Image titled Repair a Concrete Floor Step 2
    Use a ruler to determine the length and width of the area to be repaired if the condition does not define itself. This may include bumps, depressions, or ridges. Small areas of shallow surface irregularities may be concealed with a floor leveling compound, rather than chipping out and replacing the actual concrete.
  3. Image titled Repair a Concrete Floor Step 3
    Chip the surface of the concrete to remove any high material, and to create a rough surface for the repair cement mixture to bond to. For small jobs, a chipping hammer will be all you need, but larger repairs are much easier with an electric chipping hammer or even a jack hammer. Professionals also use grinding machines to prep the surface for repairs.
  4. Image titled Repair a Concrete Floor Step 4
    Clean the dust and debris from the area you have chipped. This will allow the new material to have a solid surface to adhere to. A wire brush is a good choice for this step. A stiff bristled broom or paintbrush will also work. Depending on the age and condition of the concrete chemical cleaning may be required, it is best to consult a pro.
  5. Image titled Repair a Concrete Floor Step 5
    Mix the cement/sand material you will use to fill in the area you have chipped out. Mix the dry ingredients first, using a proportion of 1 part Portland Cement (type I or II) to 2 1/2 parts clean masonry sand.
  6. Image titled Repair a Concrete Floor Step 6
    Add a latex or polymerized liquid bonding agent to the dry sand/cement mixture, using enough to thoroughly wet the material and bring it to a stiff, plastic consistency. Note that some bonding agents are applied directly to the area to be patched, like glue, so follow the instructions on the manufacturer's label.
  7. Image titled Repair a Concrete Floor Step 7
    Wet the area where the patch is to be applied with clean, fresh water. Do not flood the area, but make sure all surfaces are dampened, to assist in adhering the new cement mixture, as well as keeping the mixture from drying too quickly. Dry surfaces simply draw the moisture from the cement mixture too quickly, and will cause it to shrink, and ultimately, to crack.
  8. Image titled Repair a Concrete Floor Step 8
    Scoop some of your cement mixture out of your mixing container with a bull-nosed pointing trowel (or other suitable tool). Place the mixture into, or on the patch location, and work it into the space forcefully with the trowel to force out any air bubbles.
  9. Image titled Repair a Concrete Floor Step 9
    Level the surface of the wet cement with the trowel, leaving it slightly higher than the adjacent edges, to allow for settling and shrinkage. Allow it to dry and become stiff for an hour or so, depending on humidity and temperature.
  10. Image titled Repair a Concrete Floor Step 10
    Trowel the area with a steel finishing trowel when the patch material has become stiff. This will flatten and smooth the surface, and cause cement paste to rise to the surface. Very large, deep areas may be floated with a magnesium float to bring more cement paste up. This paste is the material that forms the surface of the finished slab.
  11. Image titled Repair a Concrete Floor Step 11
    Give the area another hour or two so that it sets up, or becomes hard, then finish trowelling it. At this point, you may need to splash a little water on the surface to slow the drying, as well as making the finishing process somewhat easier. Use the edge of your trowel to shave, or scrape off any of your cement mixture which has spread to the adjacent, finished surface. Another good choice for patching materials are hydraulic cements. They usually set up in less than 30 min.
  12. Image titled Repair a Concrete Floor Step 12
    Clean your tools, and remove any excess material.


  • For very small patches, you may purchase polymer fortified or premixed dry patching material.
  • Protect the repair from direct sunlight. A cardboard box will work.
  • Mix enough cement and sand to finish the entire patch at one time.
  • Cement with high lime content is more flexible and may be more appropriate for the repair.
  • Once the repair is done, keep it wet for a few days if possible. Use lots of water.
  • For high spots in a concrete floor that will receive a floor covering, you may be able to remedy the problem using a grinder equipped with a masonry grinding wheel.
  • For large cracks, a concrete staple may be used to stabilize and restore strength to the slab.
  • You can purchase DIY crack repair kits that come with everything you need to complete the job as well as detailed instructions for use.


  • Wear eye protection, a dust mask, and gloves when chipping, grinding, or placing concrete.
  • Quick setting cement shrinks more and leaves more cracks.
  • Always wear gloves when working with concrete to avoid cement burns.
  • If you plan to stain the concrete floor after making repairs, patching may prove problematic. Patched areas often react differently with stains than the rest of the concrete, resulting in a strange discolored area. To avoid this possibility, the entire concrete surface can be overlaid to create a uniform canvas for the stain.

Things You'll Need

  • Portland cement
  • Clean masonry sand
  • A bonding agent
  • Clean water
  • Concrete tools

Article Info

Featured Article

Categories: Featured Articles | Concrete