How to Make Your Own Underwater Aquarium Filter

Three Methods:Making a Sponge FilterMaking a Capsule FilterMaking a Bottle Filter

Filters can be expensive. Sometimes, it is hard to find the right type of filter, especially if you have a large tank, or fragile fish (such as bettas). Because of this, many aquarium hobbyists choose to make their own filters. This article will show you how to make a few different ones.

Method 1
Making a Sponge Filter

  1. Image titled Make Your Own Underwater Aquarium Filter Step 1
    1
    Choose a plastic tube large enough to fit the intake valve on your powerhead. The tube does not need to be very long, since the powerhead will be going under water. Plan on getting something at least twice the height of your sponge.
    • When choosing a powerhead, get something that will pumps twice as much water per hour as what's in your tank.
    • Sponge filters are ideal for delicate tanks.
  2. Image titled Make Your Own Underwater Aquarium Filter Step 2
    2
    Choose a filter sponge and cut it down to fit your tank. What brand you use does not matter, but it needs to be the type of sponge used in aquarium filters. The easiest shapes to work with are a triangle or a cylinder. A triangle would fit the easiest in the corner of your fish tank. A cylinder may look neater, however. What ever shape you choose, make sure that is wider than your plastic tube.[1]
    • You can find filter sponges in pet stores and fish tank stores.
    • Consider getting a sponge with larger pores. They are better at housing the good bacteria, which help clean your tank.[2]
    • Sponge filters are ideal for shrimp and betta tanks. They are bio efficient, but don't create a lot of suction or water movement.[3]
  3. Image titled Make Your Own Underwater Aquarium Filter Step 3
    3
    Measure the height of the sponge, and make a mark on the plastic tube. The mark needs to be the same height as the sponge.[4] You will be making air holes in the tube below this mark. These holes will be inside the sponge.
  4. Image titled Make Your Own Underwater Aquarium Filter Step 4
    4
    Punch holes into the tube below the mark. You can use a heated nail and hammer to punch the holes, or an electric drill. Plan on making 8 to 10 holes per inch (2.54 centimeters) of plastic tubing.[5]
  5. Image titled Make Your Own Underwater Aquarium Filter Step 5
    5
    Plug the bottom of the tube. Make sure that you are plugging the end with all the holes in it. The tube will be going into the sponge, but the bottom still needs to be plugged up. You can use a pvc end cap that fits your tube, or even a piece of styrofoam.[6]
  6. Image titled Make Your Own Underwater Aquarium Filter Step 6
    6
    Poke a hole in the sponge with your finger, then slide the tube in. Push it all the way down to the bottom of the sponge. All of the holes in the tube should now be covered by the sponge.
  7. Image titled Make Your Own Underwater Aquarium Filter Step 7
    7
    Attach the plastic tube to the intake valve on your powerhead. The powerhead will suck the water in, causing it to go through the sponge. All the mess in your aquarium will get caught in the sponge.
  8. Image titled Make Your Own Underwater Aquarium Filter Step 8
    8
    Cut a piece of airline tubing and plug it into the outtake valve of the air pump. The airline tubing doesn't have to be very long. About 3 to 4 inches (7.62 to 10.16 centimeters) will be enough.[7] The clean water will flow out of this tube.
  9. Image titled Make Your Own Underwater Aquarium Filter Step 9
    9
    Place the filter into the fish tank. If your air pump came with suction cups, use those to attach it to the wall of your tank. Angle the output tube so that the water will come out near the surface.

Method 2
Making a Capsule Filter

  1. Image titled Make Your Own Underwater Aquarium Filter Step 10
    1
    Find a small, cylindrical capsule. Film canisters, prescription containers, and empty fish food containers are perfect for this. These filters are great for small tanks.
  2. Image titled Make Your Own Underwater Aquarium Filter Step 11
    2
    Clean the capsule using hot water. Do not use any soaps or chemicals, or you will kill your fish. If you are using a film canister, clean it with water and a few drops of a tap water conditioner. Make sure that the conditioner says that it will remove heavy metals. This is because film canisters usually contain traces of heavy metals.
  3. Image titled Make Your Own Underwater Aquarium Filter Step 12
    3
    Cut a notch into the bottom end a plastic tube. Find a ½ inch (1.27 centimeters) wide plastic tube. Cut it down to 6 inches (15.24 centimeters) long. Cut a notch into the bottom of the plastic tube. You can also cut the bottom of the tube at an angle. This will help the water flow better.
    • You can find plastic tubes at fish tank and pet stores. You may also find them in home improvement stores.
  4. Image titled Make Your Own Underwater Aquarium Filter Step 13
    4
    Cut a hole in the capsule's lid. The hole should be just a little smaller than your ½ inch (1.27 centimeters) tube. This is so that you get a snug fit, once you put the tube in. You can cut the hole right in the middle of the lid, or close to the edge.
  5. Image titled Make Your Own Underwater Aquarium Filter Step 14
    5
    Put the lid onto the capsule and slide the tube all the way down into the capsule. The notched/angled bottom of the tube should be hitting the bottom of the capsule. If you cut the hole close to the edge of the lid, angle the tube so that the notch is facing the center, not the side of the capsule.
  6. Image titled Make Your Own Underwater Aquarium Filter Step 15
    6
    Poke holes into the capsule lid using a heated nail and hammer or electric drill. If you take a look at your lid, there should still be some flat area left around the tube. Fill this area with small holes. This is where the bubbles will come out of.
  7. Image titled Make Your Own Underwater Aquarium Filter Step 16
    7
    Drill a small hole into the side of the tube. Keep the tube inside the capsule/lid. Measure ½ inch (1.27 centimeters) up from the seam, where the tube meets the lid. Make a small mark. Then, make a hole right on the mark. You can use a heated nail and hammer or an electric drill to do this. The hole should be large enough for a piece of airline tubing to fit through snugly.
    • Make the hole just a little smaller than the airline tubing. This will give you a tight fit.
  8. Image titled Make Your Own Underwater Aquarium Filter Step 17
    8
    Push the airline tubing into the small hole. Keep feeding it down the bigger tube, until it is about halfway down the capsule. It should not touch the bottom of the capsule.
  9. Image titled Make Your Own Underwater Aquarium Filter Step 18
    9
    Lift the lid out of the way. Do not pull the plastic tube out. Keep it pressed firmly against the bottom of your capsule. You will be filling the capsule with filter media next. If you pull the tube away now, the filter media will get stuck under it.
  10. Image titled Make Your Own Underwater Aquarium Filter Step 19
    10
    Fill the capsule with your filter media. You can use zeolite, or any other media used in aquarium filters. Activated charcoal is a great, cheap alternative. It works well for removing bacteria. Check your local pet store or fish tank store.
  11. Image titled Make Your Own Underwater Aquarium Filter Step 20
    11
    Close the lid tightly, and place the capsule at the bottom of your fish tank. The plastic tube and capsule will both be under water. The airline tubing will go out of the water, and to the air pump.
  12. Image titled Make Your Own Underwater Aquarium Filter Step 21
    12
    Attach the other end of the airline tubing to the air pump. Depending on how deep your tank is, and how far away your air pump is, you may need to cut the airline tubing down. Measure the tubing first and trim it down if needed. Plug it into your air pump once it is the right length. Your filter is now ready to use.[8] Position the

Method 3
Making a Bottle Filter

  1. Image titled Make Your Own Underwater Aquarium Filter Step 22
    1
    Choose a water bottle that fits the powerhead. The neck of the bottle should fit right over the intake valve of the powerhead. Remember to choose the right powerhead for your tank; it should pump twice as much water as what's in your tank per hour.
    • The more powerful your powerhead is, the larger bottle you will need.
    • Bottle filters are great for large tanks.
  2. Image titled Make Your Own Underwater Aquarium Filter Step 23
    2
    Cut a large notch into the bottom of the bottle. Cut about two-thirds of the bottom corner out, but leave part of the base intake, or your filter media will fall out. This is where the water will come in and out of.
  3. Image titled Make Your Own Underwater Aquarium Filter Step 24
    3
    Fill the bottle a third of the way with filter floss. You can find filter floss in your pet store or in a fish tank store. Try to pack the floss into the bottle, so that it is dense. The filter floss will catch debris.
  4. Image titled Make Your Own Underwater Aquarium Filter Step 25
    4
    Add some activated charcoal, or any other filter media. About 2 inches (5.08 centimeters) should be enough.[9] The charcoal will filter out bacteria and toxins.
  5. Image titled Make Your Own Underwater Aquarium Filter Step 26
    5
    Fill the rest of the bottle with more filter floss. Remember to pack the filter media somewhat, so that it is snug. The will help filter out the biggest pieces of debris.
  6. Image titled Make Your Own Underwater Aquarium Filter Step 27
    6
    Consider wrapping the bottom of the bottle with some fine mesh material. This is not necessary for all tanks, but if you have shrimp, small fish, or delicate fish, this would be a very good idea. Simply wrap some mesh over the hole, and secure it with string. Women's hose are great for this.[10]
  7. Image titled Make Your Own Underwater Aquarium Filter Step 28
    7
    Stick the intake valve of the powerhead into the mouth of the bottle. The intake valve will suck the dirty water into the bottle. The filter media inside will clear all of the dirt out.
  8. Image titled Make Your Own Underwater Aquarium Filter Step 29
    8
    Fit a piece of airline tubing onto the output nozzle of the powerhead. A 3 inch (7.62 centimeters) long piece will be enough. The clean water will come out of this tube.
  9. Image titled Make Your Own Underwater Aquarium Filter Step 30
    9
    Place the filter in your tank. If the powerhead has suction cups, use them to attach it to the wall of your tank. Angle the airline tubing towards the surface of the water.

Tips

  • Initially, the filter will only pick up pieces of debris and feces in your tank. But as time progresses, bacteria beneficial to your tank will accumulate in the sponge material, allowing the filter to perform biological filtration of your water as well.
  • If you have an adjustable power pump or powerhead, make sure that the output power is set at a desirable level for your type of fish tank.
  • You can bury half of your filter in your tank's gravel to keep it secure, or have it stand upright.
  • Make sure your powerhead or pump is size-appropriate for your fish tank. It should pump at least twice as much water as what's in your tank.

Warnings

  • Regularly check your filter to make sure that it is still working. A malfunctioning pump is hazardous for your fish as well as you.
  • Never use soap or chemicals to clean anything you'll be putting inside your fish tank. Even the slightest residue will kill your fish. Use hot water only, and aquarium water conditioner if needed.

Things You'll Need

Making a Sponge Filter

  • Filter sponge
  • Knife
  • Plastic tube
  • Hammer and nail or electric drill
  • Airline tubing
  • Powerhead

Making a Capsule Filter

  • Capsule (film canister, prescription container, fish food container
  • ½ inch (1.27) thick plastic tube
  • Airline tubing
  • Nail and hammer, or electric drill
  • Filter media
  • Air pump

Making a Bottle Filter

  • Powerhead
  • Water bottle
  • Aquarium filter floss
  • Activated charcoal
  • Airline tubing

Article Info

Categories: Aquariums