wikiHow to Change a Truck AC Accumulator and Expansion Valve

Air conditioning systems rely on an accumulator to store refrigerant after it leaves the evaporator coils on its way to the compressor. This allows remaining liquid refrigerant to evaporate before continuing through the system and the device contains a desiccant to remove any moisture the system contains. Here are steps to help you change your accumulator as well as the expansion valve in your truck AC.


  1. 1
    Check your local laws to make sure it is legal for a non-certified individual to do this type of work. Since it will require purging any refrigerant, and purchasing replacement refrigerant, some jurisdictions may require a license to do the work.
  2. 2
    Make sure changing the accumulator is necessary. Since the accumulator contains a desiccant to remove moisture from the refrigerant, if the system has been discharged and improperly recharged or needs recharging, changing the accumulator will help ensure the system works efficiently after recharging. It is also recommended the accumulator is replaced whenever a compressor is replaced as well.
  3. Image titled AC pix3.JPG
    Buy the needed parts. You can order a new accumulator from suppliers online, your local auto parts dealer, or from your vehicle manufacturer dealership parts store. Buy a replacement expansion valve (also known as an orifice tube) if you plan to replace it as well. The expansion valve is located in the refrigerant tubing at the bottom of the evaporator coils, and as with the accumulator, they can collect debris which impede their performance if the system has been compromised. Also, when changing the compressor, replacement of the expansion valve is usually a requirement for warranty coverage of the new compressor.
  4. Image titled AC pix6.JPG
    Remove or discharge any remaining refrigerant from the AC system. It is better to have this done at a shop that has a refrigerant reclamation machine, but if the system is already discharged, this step can be skipped. Simply loosen the schrader valve on the low pressure (suction) charging fitting and listen for escaping refrigerant to determine if the system is still charged.
  5. 5
    Remove the pressure sensor connector from the accumulator. This can usually be unplugged, but be careful, as there may be a clip that needs to be depressed or pried up to release it.
  6. Image titled AC pix8.JPG
    Loosen the inlet and outlet couplings on the accumulator. Use the correct wrenches, and make sure the fittings do not allow the refrigerant lines to twist. You may to need two wrenches, one on the fitting and another on the compression nut that secures it to prevent damaging the refrigerant lines.
  7. Image titled ACpics11.JPG
    Loosen the clamp or support device that secures the accumulator in position. You can now completely remove the couplings and lift the accumulator out of the engine compartment. Make sure to keep it upright, as refrigerant oil and other nasty liquids may be in the bottom of it.
  8. Image titled ACpics06.JPG
    Loosen the fittings that join the high pressure refrigerant line near where it enters the bottom of the evaporator coil. Be sure to use a wrench on both nuts, since one is soldered onto the line and allowing it to twist will damage it. After the coupling is completely loosened, you can pull the two pipes apart.
  9. Image titled AC picx18.JPG
    Look for a plastic (usually) tab just inside the tubing leading into the evaporator coil housing. You can grip this with a pair of needle nosed pliers to pull the expansion valve (again, also called the orifice tube) from the tube. Note that refrigerant oil may leak from the tube if any has accumulated in the evaporator coils.
  10. Image titled ACpics04.JPG
    Blow out the evaporator coils with compressed air or compressed nitrogen to make sure no oil or debris is clogging them.
  11. Image titled ACpics05.JPG
    Install the new expansion valve, the tapered end with an o ring should go in toward the evaporator coils. Check to see if the o ring in the refrigerant line coupling is still in good condition, then reattach the fittings that connect this pipe.
  12. Image titled ACpics16.JPG
    Install the new accumulator into its mounting bracket or support.
  13. Image titled ACpics09.JPG
    Install the pressure sensor in the new accumulator. You can either buy a new one, or remove the one from the old accumulator and reuse it. If reusing your old one, it is generally a good idea to use a new seal or o ring when reinstalling it.
  14. Image titled AC picx11.JPG
    Install new o rings on the refrigerant line fittings on the accumulator, then reconnect the fittings and tighten them securely. You should now be able to either charge the system with new refrigerant or have it done at a licensed auto repair shop. Continue reading for basic instructions if you plan to proceed yourself.
  15. Image titled ACpics14.JPG
    Use a vacuum pump to evacuate the air conditioning system so no moisture remains in it. Allow the pump to hold a vacuum for at least 90 minutes before recharging the system.
  16. Image titled ACpics18.JPG
    Attach a refrigerant charging hose to a can of refrigerant, puncture the can (follow the instructions on the can if using 12 oz cans that require it), vent the air from the hose, and make sure the fittings are not leaking.
  17. 17
    Start the engine and turn the AC on high cool and high fan. Open the charging valve and allow the refrigerant to enter the system. This can be a very slow process depending on the ambient temperature, do not rush it.
  18. 18
    Test all fittings for leak using a foaming soap mixture, clean up, and dispose of old parts and cleaning products safely.


  • Purchase all items needed including replacement refrigerant before starting. Have the vehicle information such a year and make, and engine size available when shopping for parts.
  • You may need to rent or borrow an AC vacuum pump and charging manifold for this project if you don't own one.
  • Check the AC label in the engine compartment to determine the type of refrigerant and system capacity.
  • Always leak test all components when doing AC service work, since refrigerants are expensive and cause environmental damage when vented to the atmosphere.


  • Venting refrigerant can be dangerous. Do not remove any fittings from a charged system.
  • Do not over-tighten fittings with o ring seals, tighten them snuggly and check for leaks with a soap mixture after completing the project.
  • It is generally a good idea to remove the battery cable when working under the hood of a vehicle, you will have to reconnect it when charging the system.
  • Venting refrigerants may be illegal in your location.

Things You'll Need

  • New accumulator and o rings
  • Expansion valve
  • Refrigerant (usually R-134a)
  • Wrenches
  • Cleaning supplies

Article Info

Categories: Car Maintenance and Repair