User Reviewed

How to Build a Garage Work Bench

Two Methods:Build a Custom-Sized WorkbenchBuild a Sturdy Floating Shelf to Use as a Workbench

A Workbench is the most important tool in any shop. To make either a traditional Workbench or a floating-shelf bench that maximizes space, follow these instructions.

Method 1
Build a Custom-Sized Workbench

  1. Image titled Build a Garage Work Bench Step 1 preview
    Determine the dimensions of the Workbench. Measure the desired length, width, and height relative to your work space and write these dimensions down.
  2. Image titled Build a Garage Work Bench Step 2 preview
    Find a bench top. You can use thick, wooden, butcher-block-style Workbench tops (which are quite pricey), thin, hard, wooden sheets for industrial bench tops (which are more affordable), or a few pieces of plywood stacked on top of each other. For a thick, sturdy, affordable alternative, salvage a solid-core door; check your local listings, find a rebuilding center, or even ask around at a building undergoing renovation. The most important thing to keep in mind is that the Workbench should be flat and sturdy.
    • Cut the bench top to size if necessary.
  3. Image titled Build a Garage Work Bench Step 3 preview
    Cut four legs from 4x4s. The length of each leg should be the desired height of the bench minus the thickness of the bench top.
  4. Image titled Build a Garage Work Bench Step 4 preview
    Cut four leg braces from 2x4s. If you want the top of the Workbench to be flush with the frame underneath it (which you will be building in Steps 8 and 9), each brace should be equal to the width of the bench top minus the width of two 2x4s; however, if you’d like the frame to jut slightly out from underneath the bench top, which can be useful for storing clamps, for example, cut the braces to same length as the width of the bench top.
    • Since 2x4s aren’t actually 2 x 4 inches and can sometimes even vary in thickness, measure the (skinny) width of your 2x4s for a precise cut.
  5. Image titled Build a Garage Work Bench Step 5 preview
    Position each top leg brace on a pair of legs. Lay down two of the 4x4s perfectly parallel to one other so that the distance from the outside left edge to the outside right edge equals the length of the brace. Lay one leg brace across them so that it is flush with both the sides and (what will eventually be) the tops of the legs. Repeat on the other leg pair.
  6. Image titled Build a Garage Work Bench Step 6 preview
    Bolt each top leg brace to a pair of legs. Using a 3/8-inch (10-mm) drill bit, drill two holes clear through both the 2x4 and the 4x4. Make sure to drill the holes at a diagonal from each other (i.e. one at the top left, one at the bottom right) so that you will later be able to fit a third bolt into the space between. Moving from the 2x4 to the 4x4, slide bolts through the pre-drilled holes. Close them by sliding washers over the ends and holding them in place with nuts, which you can tighten with a wrench. When you’re done, the bolt ends should stick out of the 4x4s. Repeat on the remaining leg pair.
  7. Image titled Build a Garage Work Bench Step 7 preview
    Bolt the bottom two leg braces to the legs. Flip one of the leg pairs over and repeat the process you followed in Steps 7 and 8 with another brace; however, instead of lining the brace up with (what will eventually be) the bottoms of the legs, raise them a few inches so that they won’t sit flush with the floor. When you’re done, you will have a top brace at the top of one side of each leg pair and a bottom brace near the bottom of the other side of each leg pair.
    • If you would like to build a low shelf across the bottom braces, position them accordingly provided that they do not rise above 1/3 of the height of the legs; the lower the braces, the more stable the bench will be.
  8. Image titled Build a Garage Work Bench Step 8 preview
    Cut two top supports from 2x4s. Each support should equal the length of the bench top.
  9. Image titled Build a Garage Work Bench Step 9 preview
    Bolt the top supports into place. Lay the leg pairs down with the top braces facing outwards (i.e. away from one another) so that the distance from the outside left edge to the outside right edge equals the length of the top support. Place one of the top supports across the leg pairs so that it lines up with the top braces. Pre-drill a hole through the top support and into the 4x4 on either side (making sure to drill between the existing bolts) and then bolt the support into place with coach bolts. Flip the structure over and repeat on the other side. When you’re done, your four legs should be surrounded by a frame at the top.
  10. Image titled Build a Garage Work Bench Step 10 preview
    Attach the Workbench top. Lay the piece(s) in place and pre-drill bolt holes downward through the underlying supports where necessary. Screw coach bolts into place to secure.
    • If you have a thick bench top, consider bolting from the bottom up; this will keep the bench top smooth and bolt-free. However, only do this if the bench top is thick enough that it won’t risk popping off of the bolt ends.
  11. Image titled Build a Garage Work Bench Step 11 preview
    Attach a low shelf if desired. Simply measure the dimensions between all four legs, cut a shelf to this size from your desired material (ex. plywood), and screw into place.
  12. Image titled Build a Garage Work Bench Step 12 preview
    Finish the bench if desired. Sand the wood smooth and apply stain, varnish, polyurethane, etc.

Method 2
Build a Sturdy Floating Shelf to Use as a Workbench

  1. Image titled Build a Garage Work Bench Step 13 preview
    Attach a long 2x4 (38×89 mm) horizontally to the wall studs. (If your wall is solid brick, stone, etc., this method will not help you). The length of the 2x4 will be the length of the workbench and should be sized accordingly. (In this example, we are using a 16-foot / 4.8-meter piece.) Use a spirit level to make sure that this is attached horizontally.
    • Depending on the steel shelf brackets you have (and how far the hole is from the bend in the bracket), you may need a 2x6 (38×140 mm) instead.
    • The top of the 2x4 strip in this example is 3 to 3.5 feet (approximately 1 meter) off the ground. If you need park a vehicle in your garage and it needs to fit underneath the shelf, account for any additional clearance required (i.e. your vehicle's hood).
    • Use 2.5-in / 6.5 cm screws (or 3-in / 7.5-cm screws if going through drywall) to attach the 4-in (89-mm) flat face against the garage wall studs.
  2. Image titled Build a Garage Work Bench Step 14 preview
    Attach another piece of timber of the same dimensions below the first one. The gap between the two parallel strips should be determined by the length of the steel shelf bracket.
  3. Image titled Build a Garage Work Bench Step 15 preview
    Attach the shelf brackets to the two strips. The heavier duty the shelf bracket, the better. The top of the bracket is flush with the top surface of the upper strip. Use a plywood piece on top (a temporary shelf) and then butt the shelf bracket against it. Use 1.5-in (3.8-cm) screws to then attach the brackets. You will end up with two strips against the wall with a row of shelf brackets attached to them. The shelf brackets should be spaced approximately 2 feet (.6 meters) apart.
    • If desired, shelf brackets can be alternated; heavy duty, lighter duty, heavy duty, etc. in order to accommodate toolbox placement and to be able to comfortably pull up a chair underneath the workbench.
  4. Image titled Build a Garage Work Bench Step 16 preview
    Cut 3/4-in (2-cm) thick plywood into 2-ft (.6-m) wide planks. A 4x8 ft (1.2 x 2.4 m) sheet will work well for this purpose. Place one of the planks on the shelf brackets and screw the plank to the upper strip at the top/rear. Place the second plank next to (left or right of) the first one and join the two end-to-end with a 6 in (15.25cm) x 18 in (45.7 cm) piece of plywood underneath the two plank ends.
  5. Image titled Build a Garage Work Bench Step 17 preview
    Place another strip across the top of the shelf and screw into the wall studs.
  6. Image titled Build a Garage Work Bench Step 18 preview
    Apply a front strip along the bottom edge of the shelf. Glue and screw a 1.5 in (3.8 cm) by 3/4 in (1.9 cm) maple strip that's as long as your shelf. This strengthens the Workbench top while absorbing wear and tear.
  7. Image titled Build a Garage Work Bench Step 19 preview
    Attach drawers to the underside of the shelf. These thin drawers will accommodate any small tools you may have. The drawers should be 2 feet (.6 meter) wide, have a depth of 1.5 in (3.8 cm), and stretch 18 in (45.7 cm) to the back. To make and attach the shelves:
    • 1x4 ((19×89 mm) pine strips can be attached to the bottom of the shelf. The short part of the strip can be attached with glue and screws to the plywood sheet.
    • Attach metal drawer slides to the strips.
    • Construct drawers with a hardboard base and pine sides (1x2in or 2.5 by 5 cm). Edges hold the matching drawer slides. These drawer boxes are then slid into the pine strips that are attached to your plywood plank.


  • Adding 4x4 posts as legs to the front edge of the floating workbench will greatly increase its strength, which is important if you are going to be using it for pounding on things with a hammer.
  • Always bring a tape measure (minimum 20 feet or 6 meters long) to the store with you when purchasing wood. Wood is commonly mixed around by the customers by accident or cut into smaller lengths and placed back on the rack. Being able to measure out your lengths while shopping can save you time in returns!
  • Using an orbital sander with 80 grit (then moving up to 150 grit) can give your entire table top a great, even surface. This also prepares it for varnish. Use the 220 grit between varnish coats for best results.
  • Figure out the lumber measurements before buying them; many lumber and home improvement stores will cut lumber for you if you ask, which will greatly reduce your work time.
  • A top of 1/8" (3 mm) or 1/4" (6 mm) Masonite (hardboard) will make a very strong surface.
  • Make sure you buy a hard wood(tends to have a darker colour).
  • Instead of using steel nails which tend to "back out" over time, use exterior-grade deck screws. They are significantly easier to remove than nails if you ever need to replace the bench.
  • Stain/varnish combinations do not seal and protect as well as 2-3 coats of varnish alone. If you use this combination product, consider additional layers of varnish as well, especially if you intend on the table receiving heavy use.
  • Use a router with a round-off bit (1/8" to 1/4" or 3 mm to 6 mm depending on your preference) to finish off the maple strip edge of the floating shelf for a professional look.
  • Screws are better than nails for the floating shelf project. Drywall screws are cheap, come in many lengths and are easy to drive, but they are for hanging drywall and nothing else; instead, purchase high-quality screws, i.e. Floor or deck screws. Invest in a battery powered drill/driver to make short work of driving them.
  • Consider mounting a light above your work surface. Used pool table lighting can be purchased quite cheaply and adds a bit of decor to a garage, but any type of lighting at all will add considerable value to your workspace.


  • The US lumber industry shortens each 2x4 by half an inch on either side for various reasons (shrinkage, smoothing). A standard 2x4 will actually measure somewhere around 1-1/2 x 3-1/2 inches.

Things You'll Need

Custom-Sized Workbench

  • Bench top (ex. premade top, plywood, solid-core door)
  • Four 4x4 legs
  • Four 2x4 leg braces
  • Two 2x4 top supports
  • Saw
  • Drill
  • 3/8-in (10-mm) drill bit
  • Twelve 3/8-in (10-mm) bolts with washers and nuts
  • Coach bolts (number may vary)
  • Material such as plywood for bottom shelf (optional)

Floating Shelf

  • Required Tools:
    • Circular saw (18v model recommended)or a Jigsaw
    • Drill/screwdriver (18v cordless model recommended)
    • 2-4 foot bubble level
  • Optional Finishing Tools:
    • Orbital, Belt or Finish Sander w/ 80, 150 & 220 grit paper
    • Router with 1/8" / 1/4" rounding bit.
  • For Workbench:
    • 8' x 4' 3/4in maple plywood ($34)(or other hardwood)
    • 2" x 4" x 16' [x3]($4 each)
    • 18" (up to 20") steel Shelf Brackets.
    • 1-1/2" x 3/4" x 16' maple strip for front edge
    • 1-1/2" x 3/4" x 4'-1-1/2" maple strip for side edges (or other hardwood)
    • 2-1/2"-3" screws, (to secure 2x4s to wall studs, 3" screws if securing to studs through drywall)
    • 1-1/2" screws (to secure brackets to wall mounted 2x4s & pine edges)
    • 3/4" screws (to secure brackets to underside of table-top)
    • Polyurethane glue ($4)
    • Polyurethane varnish
  • For Drawers:
    • 2" x 4" x 16' [x1]($4 each) for drawer cross pieces.
    • Hardboard sheet for drawer bottoms ($17)
    • 1" x 2" pine boards for drawer sides($15 worth)
    • 1 set of drawer slides for each drawer you make

Article Info

Categories: Furniture and Cabinets